Cart 0
MAH 485

MAB 845

Ø 100 mm Core Drilling & M30 Tapping with Swivel Base

Technical Specs

360° 360°
Core drill short 30 mm
12-100 mm
Core dril long 55 mm
12-100 mm
Core drill extra-long 110 mm
20 -60 mm
Thread cutting
<= M30
Countersinking
<= 50 mm
Reaming
<= 31.75mm
Twist drilling
<= 31.75 mm
Friction clutch
----
Permanent internal lubrication
Yes
Speed range 1
40 -110 min -1
Speed range 2
65-175 min-1
Speed range 3
140 - 360 min-1
Speed range 4
220 - 600 min-1
Morse taper
MT 3
Quick change drill chuck-system
Keyless 19 mm
Industrial arbor
MT 3,32 mm weldon
Direct arbor
----
Weight
25 kg
Magnet Size
110 x 220 x 54 mm
Stroke
255 mm
Voltage
230 V AC , 50-60Hz
Motor Output
1800 Watt
Swivel Base
Yes
Carbon brush wear control
Yes
CW/CCW rotation
Yes
Overheating protection
Yes
Magnet indicator
Yes
Full wave control electronics
Yes
Torque Control
Yes

The made in Germany, MAB 845 Mag Drill. The MAB 825 magnetic drilling machines can also be bought with a Swivel Base option (the model is then called MAB 845). The Swivel Base is an adjustment device on BDS magnetic core drilling machines, which helps the operator to position the machine ”even under magnetic condition.” The operator can move the machine 30° left or right and 20 mm backward or forward that too when the magnet is activated. This is a useful when drilling multiple holes close to each other (like on boiler plates) or when drilling in vertical position or overhead position. Overheat protection. One of the very useful feature of MAB 825 / MAB 845 specially for new operator is the overheat protections. Due overload or improper handling of the machine while drilling the machine may get heated and due to heat the motor may get damaged. The BDS magnetic drilling machines protects the machine from overheat by shutting down the motor when the sensors senses overheat, this prevents in damaging of the motor. After the motor is shut down by the overheat protection, keep the machine idle for 30 seconds to 1 minute and then run the run the motor again without drilling. Run the motor for a minute and then start to drill again. This feature increases the machine service life as well as avoids accidents.

100 mm

Drilling Capacity

M 30

Tapping Capacity

1800 Watt

Powerful Motor

25 Kg

Weight

Swivel base adjustment feature

Four-stage oil bath gearbox

Full wave control electronics

Reversible motor

Magnet indicator

Swivel Base

Safe switches

Complete internal cabling

Quick Change Drill Chuck

Industrial arbor

Ejector pins

Carry case

Safety chain

Torx screwdriver

Drill drift

Ejector pins

Operating manual

Product Videos

GSW

Quick Change drill chuck

Moreinfo

GSE

Standard Quick Change Insert

Moreinfo

GSS

Quick Change Insert Safety friction clutch

Moreinfo

ZGA

Economic Tap Adapter

Moreinfo

ZSS 200

Keyless Quick Change Drill Chuck System

Moreinfo

ZVH 220

Extension Bush DIN 2178

Moreinfo

ZAP 200

19 mm Adapter

Moreinfo

ZAF 002

Internal Thread Adapter

Moreinfo

ZAF 003

Weldon to Quick-In Adapter

Moreinfo

ZAP 300

Core Drill Extension

Moreinfo

ZAF 005

One-Touch to Weldon Adapter

Moreinfo

ZAF 004

Quick-In to Weldon Adapter

Moreinfo

POW 100

PowerWORKER

Moreinfo

ZHS 006

High-performance cutting oil 5000

Moreinfo

ZHS 400

High-performance lubrication spray 5200

Moreinfo

ZHB 001

Cooling lubricant concentrate 6000

Moreinfo

ZSR 100

Spray cleanser 1000

Moreinfo

ZRO 250

Tube clamp for 80-250 dia. Tubes

Moreinfo

ZRO 400

Tube clamp for 150-500 dia. Tubes

Moreinfo

ZAV 400

Vaccum plate for smooth surfaces

Moreinfo

MBS 300

Magnetic Pillar

Moreinfo

ZMC 180

MobilCLAMP

Moreinfo

ZMS 500

MagnetCLAMP

Moreinfo

ZST 300

Prism Wise

Moreinfo

Site map